Badger-meter Vortex Meters Uživatelský manuál

Operator’s ManualToll Free: 888-572-2463Tel: 262-639-67708635 Washington Avenue Racine, WI 53406-3738 USARacine is a trademark of Racine Federated Inc

Page 8EDIT/IN-SERVICE MENUEntering Edit Mode and Putting Meter In-ServiceFL_METER040720RWG15Tag:PV (Volume)Model Number:Analog Output Current:Percent

Page 9Exiting Edit Mode (Or putting the meter in-service) - To put the meter in-service, click the “Edit/In-Service” pull-down menu on the Main screen

Page 10SAVING/RESTORING CONFIGURATION MENUSave/Restore Conguration Meter SettingsRacine Federated HART Interface UtilityFL_METER040720RWG15Tag:PV (Vo

Page 11Save Conguration - This command will cause the meter to copy any new settings from RAM to EEPROM. At power up, settings are retrieved from EEP

Page 12Restore Factory Conguration - This command will cause the meter to load the factory settings into RAM and EEPROM. Use this command with cautio

Page 13CONFIGURE METER MENURacine Federated HART Interface UtilityFL_METER040720RWG15Tag:PV (Volume)Model Number:Analog Output Current:Percent of Rang

Page 14Analog Range Values (Re-scaling the meter)The Analog Range settings can be read and set from the “Analog Range Values” dialog box. To bring up

Page 15Primary Variable (PV)The primary variable can be read and set from the “Primary Variable” dialog box. To bring up this box, click the “Congure

Page 16HART InterfaceThere are many HART related elds that can be viewed and set using the “HART Interface” di-alog box. To bring up this box, click

Page 17Number of Preambles - This eld allows the user to change the number in the preambles at the beginning of HART messages transmitted by the mete

TABLE OF CONTENTSMinimum System Requirements ...1Installati

Page 18Process TemperatureThe Process Temperature settings are accessed through the “Process Temperature” dialog box. To bring up this box, click the

Page 19Integrated RTD - If the meter is supplied with an integrated RTD, it is typically the best choice for the “Process Temperature Source”. The int

Page 20Process PressureThe Process Pressure settings are accessed through the “Process Pressure” dialog box. To bring up this box, click the “Congure

Page 21Process Pressure Source - There are four different sources that can be selected for the pro-cess pressure: • An absolute pressure analog input

Page 22User Dened Pressure - This eld allows the user to enter a constant process pressure. However, this pressure is only used when “User Dened” i

Page 23The main purpose of this window is to allow the user to specify the source that the meter should use for density and viscosity information. Thi

Property Table Version Number - This eld displays the version number of the loaded prop-erty table.Process Density - This eld displays the process d

LCD Display ModeThe display mode can be accessed through the “LCD Display” dialog box. To bring up this box, click the “Congure Meter” pull-down menu

Alternating PV & Totalizer - This selection causes the LCD to alternate between the PV and totalizer. This selection is only valid when the primar

Output Current and Percent of Range - This selection causes the analog output current andthe percent of range values to be output during burst mode. C

MINIMUM SYSTEM REQUIREMENTSTo run the Racine HART Interface, the user must have the following:• Microsoft Windows 98, ME, NT, or XP. (the Racine HART

Password ProtectionPassword Verification:Password:WriteReadClosePassword Protection EnabledTo password protect the meter, click the “Password Protecti

The active alarm current setting is read from the meter and displayed when this dialog box is opened. To change the setting, click the desired selecti

For shedding frequencies below the selected cut-off, the output value will be set to 0 ow. This feature is helpful at low ows where noise in the env

Totalizer SettingsRoll Over Value:Multiplier:Custom Unit:WriteReadCloseTotalizer Enabled10000000.001The value of the totalizer is stored in the meter’

Totalizer Enabled - The totalizer is running when this box is checked. The totalizer can alsobe started and stopped by checking and un-checking this b

TOOLS MENURacine Federated HART Interface UtilityFL_METER040720RWG15Tag:PV (Volume)Model Number:Analog Output Current:Percent of Range:Process Tempera

Power Up - The settings of the totalizer are stored in non-volatile memory. Therefore, if the totalizer is running (totalizing) when the meter losses

Page 35The “Property Table” dialog box is a tool used to load property tables into the meter. This dialog box can also be used to export a property ta

Page 36DiagnosticsThe diagnostics screen is typically only necessary when the meter needs to be serviced. A Racine customer service technician can ref

Save AsFile name:Save as type:Save in:SaveCancelMy ComputerMy Network P...My DocumentsDesktopHistoryMy DocsText.txt??PrintCancelPrintPage RangeAllSele

THE MAIN SCREENThe Racine HART Interface main screen displays basic meter measurements and status indicators. The main screen also provides menus that

Conguration ReportThe conguration report is a convenient tool to display all the customer congurable settings of the meter. The report generated by

CalibrationThe calibration selection is only necessary when the meter needs to be serviced. The Racine customer service technician will utilize or dir

Page 40The “Digital Pots” selection will allow the technician to change hysteresis data.CloseWriteReadDigital Pot SettingsUnfiltered Audio Hyst:Pot Va

Page 41APPENDIX A - WIRING DIAGRAMSUse foil shielded cable in all installations. Ground the foil shield to the chassis ground terminals provided on th

Analog Pressure Gauge WiringIf an analog pressure gauge is used it must be wired as shown below to avoid inadvertent cur-rent paths.A single supply ca

APPENDIX B - TROUBLE SHOOTING GUIDEProblem ResolutionLow loop voltageThe meter requires 15 volts DC at the power terminals. Measure this voltage at th

A division of Racine Federated Inc.Limited Warranty and Disclaimerracine, div. of Racine Federated Inc. warrants to the end purchaser, for a period of

8635 Washington AvenueRacine, WI 53406-3738 USA262-639-6770888-572-2463e-mail [email protected] 45

Page 3• Fixed Current Mode - This indicator is lit when the analog output current is set to a xed value. The analog output current is not dependent

Page 4Pull Down Menus• Congure Meter - This menu gives the user access to the basic meter settings.Racine Federated HART Interface UtilityFL_METER04

Page 5• Tools - This menu provides tools to the user such as analog output trimming and totalizer. Racine Federated HART Interface UtilityFL_METER040

Page 6• Save/Restore Conguration - This menu allows the user to save and recall setting from non-volatile memory (EEPROM).Racine Federated HART Inte

Page 7• About - This selection opens a dialog box that presents the Racine HART Interface soft-ware version and also provides contact information for